The Technique Of Plastering A Fencing Wall With Sand And Cement — Amazing Craft Builder
Thank for watching my video!
Subcribe my chanel: www.youtube.com/channel/UCeaGw7wK1H_5TCQm-zvR8cA
I Wish You Always Happiness
It was in spring this year when I picked up this beaten up antique hand cranked hammer drill. My friend has found it on the steel waste together with the german „Weltrekord“ ratchet screwdriver. The condition of the drill was super bad. It was very corroded, had a lot of missing screws, the handle was in very bad condition and the crank was bent so much you couldnt even make a full turn. Thats all said, it was the perfect item for a new restoration video.
At first I thought this should be a quick and easy project, but one problem after the other became visible and it turned out to be a real challenge. There was the big dent in the left side of the case. Usually you cant bend casted parts, but with a bit of heat and careful pressure on the arbor press I was able to remove it a bit. It also worked to get rid of the warping with some heat. For the finish of the housing I wanted to have an antique cast aluminium look. I thought it would look very cool if I could tumbler these parts after sandblasting. I ended up building a huge rotary tumbler from scratch and it worked very well (video link below).
Another big issue was the tool holder and the drill bit, as they were both completly rusted. Big thanks to @Hand Tool Rescue at this point for helping me out with the dimensions on these two parts by disassembling and measuring his own hammer drill. After a bit of search on eBay I found a set of original Rawlplug drill bits. After they arrived I was able to measure the shaft and the taper of the drill to then turn a new tool holder. It all worked out very well and yes, the drill only holds with the taper ;-)
Before I even started this project I just had one question in mind „How am I going to replace the messed up handle cover?“. My first idea was to wrap it in nice black leather like steering wheels are made. That would definitely work, but thats something Ive never done before so I was quite sceptical. Then the idea of a heat shrink tube came up. That would be a very easy solution, but heat shrink tubes dont have any structuires to it and it wouldnt quite fit the the rest of the tool. Thanks to the research of my Patreons and channel members, they have found very special heat shrink tubes that have a structure in it. I really liked it as it almost looked exactly the same like the original handle.
After all it was a very intense and time consuming project. Ive done so many hours of research on this one and I had to learn new skills. Im very happy how it turned out.
I hope you like my work and the video.
Huge thank you to all of my Patreon supporters and specially to:
Tonya M Broerman
Zack Thompson
Adel AlSaffar
afreeflyingsoul
Yale Baker
Gregory
Alex McGeorge
Alistair Moor
Amar.k
Bendurion
Courtney Maleport
David Barker
Greg Marston
Joshua Bentley
Lambda GPU Workstations
Luke Schmick
Luke Stone
Matt Bosch
Mellissa Marcus
Mike Schlodder
Monte Gibbs
Muzaffer Aksoy
Nick Houston
Paul Mampilly
potokslow
Todd Medbury
Vickie Bligh
Vince Valenti
Xavier Carbel
Yuri Zapuchlak
Aaron Quante
Alex Breton
alex latzko
Allen Frank
Amanda Taylor, Esq
Andreas Mimra
Andrew Phillips
Anthony Adams
Arni Bjorgvinsson
audi4444player
Blake T
Brandon Fitzwater
Brian Newton
Carlo
Chad Bryant
Chris Simondet
Grok Senften
Haley McFadden
Harper Kim
Hunter R.
Jason Koi
Jason Tarlov
Jeremy Cole
Jonas Richartz
Jordan Page
justin f.
Kelly Imgrund
Kurt Gazow
Marc Cerisier
Marius Costan
Martin Rønnow Klarlund
Mellissa McConnell
Michael Bier
Mickey Eisenhorn
Mike Donaldson
Nick Cannon
Pasacal Schmikal
Philipp
Schultes Thomas
Scott Marshall
Sergei Shvartsman
Svenja Kuckla
The Carlsons
Trevor Kam
Tucker Ifft
Warren G Strand Jr
William Wallace
웅록 윤
My camera:
Panasonic HC-VX11
If you have any questions about the process, machines im using or other stuff, just ask me in the comments. I read them all and i try to reply as soon as possible.
Sorry for my bad english, its not my language. I try my best to improve my technical english.
Subscribe for more of my content. Im uploading videos about mechanical stuff, as new creations and buildings and also restorations.
Thank you for watching :-)
Building a Huge Rotary Tumbler from Scratch — Homemade Rotary Tumbler youtu.be/c04x6ZF9kKc
العمود الحلزونى ( The spiral column)
طريقة وكيفية عمل العمود الحلزونى من البداية الى النهاية…
طريقة و كيفية عمل ( فرمة ) او زاوية العمود الحلزونى…
مقاسات(فرمة) او زاوية العمود الحلزونى 20 سم ...و30سم…
طريقة تصنيع فرمة العمود الحلزونى من الخشب…
وطريقة وكيفية شغل العمود الحلزونى من الاساس حتى التشطيب…
شرح كيفية وزن العمود الحلزونى…
واخيرا كيفية تشطيب العمود الحلزونى…
والحصول على اجمل الديكوات والتصميمات الهندسية فى عالم البناء…
وانا احبكم فى الله…
واتمنى لكم التوفيق والنجاح…
واشتركوا معى فى القناة ...فضلا منكم وليس امرا…
السلام عليكم ورحمة الله وبركاته
#ابو_حمودى
طوب brick، الطُّوبة كتلة بنائية مستطيلة الشكل مصنوعة من الطين أو الطَّفْل، أو مواد مختلفة أخرى، سنكتشف الان كيف يتم صنع و تشكيل البلاط وطوب
— Email || للتواصل والإعلان:
hossin888@gmail.com
Техника #makita в #220вольт — goo.su/1Kmn
Бесплатная доставка, подарки и безусловная гарантия от магазина 1 год при заказе аккумуляторной техники #макита
Совсем недорогой вариант для отделки и ремонта дома. Фасадная декоративня штукатурка и кирпич выполнены из клея для пенопласта. Все окрашено фасадными красками.
Музыка на фоне soundcloud.com/atch-music